
This is a general guide. Always follow the instructions from your fifth wheel hitch maker and your truck’s owner’s manual, and have your hitch installed by a qualified shop.
Every Infinity car hauler trailer connects to the truck the same way: through a 2-inch kingpin that locks into a fifth wheel hitch. Getting that hitch right is the difference between a 4, 5 or 6 car hauler that tows straight and quiet, and one that wears out parts, rides nose-high or, worst case, comes loose. This guide covers what kind of fifth wheel a car hauler trailer needs, how to set the height, how much cab clearance to leave, and a step-by-step way to hook up and check the connection every time.
Why a car hauler uses a fifth wheel and a 2-inch kingpin
A loaded multi car trailer puts a lot of weight on the truck. A fifth wheel spreads that weight over a wide, flat plate mounted over or just ahead of the truck’s rear axle, and the kingpin locks into jaws inside the hitch head. The result is a stable pivot point that handles heavy pin weight and lets the trailer turn smoothly behind the truck.
Every Infinity model, from the 4 car GN450 to the 6 car GN600, uses a standard 2-inch kingpin on a 3/8-inch bolster plate. It does not use a ball coupler. So your truck needs a true fifth wheel setup, not a ball in the bed.
What your fifth wheel must be rated for
Our trailers are rated at 25,900 lb GVWR. That’s why we ask for a fifth wheel rated for 32,000 lb or more on any truck pulling an Infinity trailer. The extra margin matters: a hitch should never be the weakest link in the setup.
Here’s a common mistake to avoid. Many bed-mounted fifth wheel hitches are built and tested for recreational camper trailers. Some hitch manuals say outright that the hitch is designed for recreational fifth wheel trailers only, and many are rated around 20,000 lb or less. A commercial car carrier trailer that hauls four to six vehicles every week is a different job. Before you buy, read the hitch’s rating label and its intended-use section, not just the price tag.
Your setup is only as strong as its lowest rating. Check all of these:
- The fifth wheel’s towing (gross trailer weight) rating and its vertical load (pin weight) rating
- Your truck’s fifth wheel towing rating and GCWR (gross combination weight rating)
- Your truck’s payload and rear axle rating, since pin weight sits on the rear axle
- The trailer’s 25,900 lb GVWR
Our guide to what truck you need to tow a 5 car hauler goes deeper on the truck ratings.
Hitch height: 46 to 47 inches
We build our car haulers to ride level with the fifth wheel plate at 46 to 47 inches off the ground. A level trailer puts the right share of weight on each axle, keeps the tandem duals wearing evenly and helps the hydraulic brakes work as designed.
If the hitch is too low, the trailer rides nose-down. That pushes extra weight onto the front axle of the trailer and can bring the front of the trailer close to the truck frame on dips. If it’s too high, the trailer rides nose-up. The rear axle carries more of the load, and the upper deck sits taller than it should. Measure from level ground to the top of the fifth wheel plate with the truck unloaded, and set the hitch to land in the 46 to 47 inch range.
Cab clearance: leave at least 54 inches
A 4, 5 or 6 car hauler is long, and when you turn, the front corners of the trailer swing toward the truck cab. We ask for at least 54 inches of cab clearance from the back of the cab to the center of the fifth wheel. That gives the trailer room to pivot in tight turns, at fuel islands and in dealer lots without contacting the cab.
Where the fifth wheel sits on the truck
Federal safety rules say the lower half of a fifth wheel must be located so that, under any load, it distributes the weight of both vehicles properly across their axles and does not interfere with steering, braking or maneuvering (49 CFR 393.70). In plain terms, the hitch usually sits a little ahead of the truck’s rear axle centerline, so some pin weight transfers to the steer axle and the truck still steers and stops well.
The same rule requires the fifth wheel to be mounted to the truck frame with properly designed brackets and bolts, without cracking or deforming the frame, and with a device that keeps it from shifting. It also requires a locking mechanism that can only be released by a positive manual release. That’s one more reason to have a qualified shop install the hitch rather than doing it in the driveway.
Chassis cab or pickup bed: GN vs GNW
Infinity builds each car hauler two ways:
- GN models (GN450, GN500, GN550, GN600) are built for chassis cab trucks, where the fifth wheel mounts on a flatbed or hauler body behind the cab. This is the classic hotshot car hauler setup.
- GNW models (GNW450, GNW500, GNW550, GNW600) are built for trucks with a pickup bed, including a dually car hauler setup.
Both use the same 2-inch kingpin and need the same 32,000 lb+ fifth wheel, 46 to 47 inch height and 54 inches of cab clearance. Not sure which fits your truck? Our GN vs GNW guide breaks it down.
How to hook up a car hauler to a fifth wheel, step by step
- Park on level, firm ground. Make sure the area is clear of people. Nobody should stand between the truck and trailer while you couple.
- Chock the trailer wheels.
- Open the hitch. Make sure the fifth wheel jaws are open and the release handle is in the unlocked position. Tilt the plate’s ramps down if your hitch has them.
- Set the trailer height. Use the trailer’s landing jack (our GN550 has a side-wind drop-leg jack) so the kingpin plate sits just slightly below the top of the fifth wheel’s ramps. As you back under, the hitch should lift the trailer slightly. Never lower the kingpin down onto the hitch from above.
- Back straight and slow. Line the center of the hitch up with the kingpin and back in slowly until the jaws lock. You’ll usually feel and hear it.
- Do a pull test. With the trailer brakes holding or the wheels chocked, pull forward gently in low gear. The truck should not separate from the trailer.
- Look at the connection. Set the parking brake and get out. Check that there is no gap between the trailer’s kingpin plate and the fifth wheel plate, that the jaws are fully closed around the kingpin (not around the head of the pin), and that the release handle is in the locked position with any safety pin or latch in place.
- Connect the electrical lines. Plug in the 7-way plug for lights and brakes, and the dual pole plug with its 4-gauge charge wire so your truck keeps the trailer’s 12-volt battery charged for the hydraulic pump.
- Raise the landing jack all the way and stow the handle.
- Remove the chocks and do a walk-around. Test the lights and brakes before you pull out.
Unhooking
- Park on level, firm ground and chock the trailer wheels.
- Lower the landing jack until it takes the weight off the hitch.
- Disconnect the 7-way and the dual pole charge line.
- Pull the hitch release handle to the unlocked position.
- Drive forward slowly, letting the trailer slide down the fifth wheel ramps onto the jack.
Keep the hitch in shape
- Keep the plate lubricated (or use a lube plate) so the trailer can pivot without binding, and keep the jaws and moving parts clean and greased per the hitch maker’s instructions.
- Check the mounting bolts and rails for tightness and cracks on a regular schedule.
- Inspect the kingpin for wear and the bolster plate for damage.
- Include the coupling in your daily inspection. Coupling devices are one of the parts federal rules list for the driver’s end-of-day inspection report.
For the full schedule, see our car hauler maintenance checklist.
Frequently asked questions
Can I use a ball hitch with an Infinity car hauler?
No. Every Infinity trailer uses a 2-inch kingpin, which needs a fifth wheel hitch rated 32,000 lb or more.
Can I use an RV fifth wheel hitch?
Check its rating and intended use. Many RV hitches are rated well below 32,000 lb and are labeled for recreational trailers only, which doesn’t fit a commercial 5 car hauler or 6 car hauler.
What hitch height do your trailers need?
46 to 47 inches from the ground to the top of the fifth wheel plate, so the trailer rides level.
Who should install the fifth wheel?
A truck upfitter or trailer shop that installs commercial fifth wheels. They can mount it to the frame correctly and set it at the right height and position for your truck.
Match your hitch to the right trailer
Compare our 4 car haulers, 5 car haulers and 6 car haulers, or contact Infinity Trailers in Haslet, Texas. We’ll walk through your truck and hitch before you order.
Last reviewed November 18, 2026.
Sources:












